Garage Door Sensor Installation in Marble Falls, TX | Garage Door USA
from $99
Garage Door Garage Door Sensor Installation Marble Falls, TX
Photo-eye safety sensor installation, alignment, and replacement. Required by UL-325 safety code — we test auto-reverse and verify the door stops on a 1.5-inch obstruction.
Garage Door Garage Door Sensor Installation Marble Falls, TX
Marble Falls's garage door sensor installation jobs land on our schedule daily. The housing here is mostly suburban single-family homes with attached garages, alongside pockets of older in-town housing, and we size every fix to match it rather than forcing a one-size part.
Garage doors in Burnet County live with a humid subtropical climate — long, hot, muggy summers, mild winters, heavy thunderstorms, and high year-round humidity. For Marble Falls that means watching for summer heat and moisture that swell wood doors and seize rollers, damp garages that pit galvanized parts over time, and morning condensation that collects on cold metal hardware; we factor it into every repair and every new-door spec.
Run down the service log for Marble Falls and the same repairs repeat: storm-driven debris and water in the tracks, sagging insulated panels softened by repeated heat and humidity, swollen, sticking wood doors in summer humidity, and rusted bottom brackets on damp slabs. We carry every part needed to close them out in one trip.
Photo-eye safety sensors are required by UL-325 on every garage door opener manufactured since 1993. They detect obstructions in the door's path and either reverse the door (during close) or refuse to start (when activated). When sensors are misaligned, dirty, sun-blinded, or failed, the door either refuses to close at all or — worse — closes without sensing an obstruction. Our sensor installation service replaces failed sensors, realigns drifted brackets, cleans the eye optics, and verifies auto-reverse on a real obstruction test.
Replacement eyes are brand-specific (LiftMaster has a different connector and signal pattern than Genie). We stock the major brands and most legacy models. Brackets occasionally need replacement when corrosion has degraded them or impact has bent them. Bracket alignment is critical — eyes that are slightly off-aim trigger intermittent close failures that drive homeowners crazy.
Every visit ends with an obstruction test: a 1.5-inch (3.8 cm) tall object placed under the door at three positions across the opening. The door must reverse when it touches the object. This is the UL-325 baseline — if the door doesn't pass, the install isn't complete. We document the test results on the work order.
Photo-eye electronics fail at 10–15 years. Replacement is inexpensive and quick.
Our process
1
Call or schedule online. Call or book garage door sensor installation online, pick the 2-hour slot that works, and we lock it in within five minutes — tech name and photo included.
2
On-site diagnosis. On arrival we diagnose the garage door sensor installation on-site — free for most repairs, $39 on minor service calls (waived if you proceed). You see the issue and the fix before we start.
3
Flat-rate quote. We quote garage door sensor installation for Marble Falls at a flat rate, in writing, before any work — no hourly billing, no commissioned upselling. The number doesn't move once you approve it.
4
Same-visit fix. Your garage door sensor installation in Marble Falls is almost always a single-visit fix — our first-call rate is 96%. We test the door alongside you and leave the space cleaner than we found it.
How much does garage door sensor installation cost in Marble Falls, TX?
What you'll pay for garage door sensor installation in Marble Falls, TX: a flat rate starting at $99, confirmed in writing up front. Senior, military, and financing options are all on the table, and the quote is good for a full 30 days. Pricing garage door sensor installation cost in Marble Falls, TX? The quote is flat-rate and in writing before any work begins — no hourly creep.
Garage Door Sensor Installation the United States starts at from $99, and the garage door sensor installation number is flat-rate, written, and set before we begin — no hourly billing, no surprise parts charges. We discount labor 10% for seniors (65+) and military, and projects over $1,500 can use 0% APR Synchrony financing for 12 months with no prepayment penalty.
Why homeowners in Marble Falls, TX choose us for garage door sensor installation
What keeps Marble Falls calling us back for garage door sensor installation: a CSLB-licensed (#1098234), background-checked crew that knows Texas's humid subtropical region, arrives in about 78 minutes, and tells you honestly when a repair beats a replacement. For professional garage door sensor installation in Marble Falls, TX, Marble Falls homeowners reach a salaried, background-checked crew, never a call center.
The garage door sensor installation carries a decade-long workmanship guarantee — independent of the manufacturer's parts warranty. Fail because of how we installed it, and we fix the garage door sensor installation at no cost for ten years. 30,000-cycle springs hold a lifetime warranty for the original homeowner, with parts and accessories backed 1–5 years by item.
Honest sizing and honest scope drive how we quote garage door sensor installation: we don't up-sell unnecessary work, our techs are salaried (not commissioned), and the diagnostic is structured so you see exactly what we see — including the parts still in good shape. If a repair is the right call we say so; if replacement is the better long-term economics, we say that. Either way the garage door sensor installation quote is flat-rate, written, and good for 30 days.
Areas we serve for garage door sensor installation
We provide garage door sensor installation throughout Marble Falls, TX and the surrounding Burnet County area. Serving Marble Falls and surrounding neighborhoods.
Context for garage door sensor installation in Marble Falls: Marble Falls lies within Burnet County, in Texas. We serve the entire county, not just the easy-to-reach parts.
Just outside Marble Falls? Our garage door sensor installation still reaches you — Meadowlakes, Cottonwood Shores, Granite Shoals, and Horseshoe Bay and the towns between are on the daily route across Burnet County. Need garage door sensor installation near 78654? It's on the daily Burnet County loop, dispatched to the closest stocked truck.
Garage Door Sensor Installation near you in Marble Falls, TX
For Marble Falls homeowners who searched garage door sensor installation near me, the advantage of going local is simple: faster arrival, a tech who knows Texas's humid subtropical region, and someone you can reach again if you ever need to.
Marble Falls is part of our greater Austin, TX metro service area.
Our garage door sensor installation trucks reach ZIP codes 78654 and the nearby area. Since Marble Falls conditions change garage door sensor installation reach times hour to hour, we hold the ETA until you call and can give you a real one. The dispatch line goes straight to an on-call tech, never to voicemail. For local garage door sensor installation in Marble Falls, TX, including 78654, we route the nearest stocked truck straight to your door.
Frequently asked about garage door sensor installation
Top questions homeowners searching for Garage Door Sensor Installation near me ask us:
Marble Falls sits in a humid subtropical climate — long, hot, muggy summers, mild winters, heavy thunderstorms, and high year-round humidity. That is hard on a door — summer heat and moisture that swell wood doors and seize rollers, damp garages that pit galvanized parts over time, and morning condensation that collects on cold metal hardware all accelerate wear on springs, seals, and openers, so the failures we see most here are storm-driven debris and water in the tracks, sagging insulated panels softened by repeated heat and humidity, swollen, sticking wood doors in summer humidity, and rusted bottom brackets on damp slabs. We size springs and seals for Texas's humid subtropical region conditions rather than a generic catalog spec.
The call we get most in Marble Falls is storm-driven debris and water in the tracks. Marble Falls has mostly suburban single-family homes with attached garages, alongside pockets of older in-town housing, so sagging insulated panels softened by repeated heat and humidity turns up often too. We carry the common parts on the truck for a single-visit fix.
1-year manufacturer coverage on replacement sensors; 10-year workmanship on the install.
UL-325 has required them on residential openers since 1993. UL-325 is the governing federal safety standard. Older openers without photo-eyes are non-compliant when replaced.
Same-brand same-generation: yes. Different generation: sometimes, depends on the model. Different brand: rarely. We match generation when ordering.
Realignment: 15–30 minutes. Sensor replacement: 30–60 minutes. Full retrofit on an older opener: 60–90 minutes.